Edelbrock Vintage 94™ Two-Barrel Carburetors


VINTAGE 94™ CARBURETORS
In 1938, when Henry Ford needed a more efficient carburetor for his new 24-stud Flathead V8 engine, he contracted development to the Chandler-Groves Company and the 94 two-barrel carburetor was born, fueling Ford engines until production ceased in 1957. Flash-forward to 2012 and the 94 is once again available, by none other than Edelbrock!
Built around Edelbrock's reputation of bolt-on performance carburetors, the Edelbrock 94 two-barrel carburetor provides nostalgic and period correct hot rods and restorations with the most accurate and best performing carburetor on the market. The Edelbrock 94 features a die-cast bowl and air horn with an aluminum 3-bolt base. A secondary version of this carburetor is available and features no choke, making it a must have for multiple carb setups. They both feature an extended throttle shaft to make it easier to install dual and triple carburetor combinations, especially when used with Edelbrock's exclusive progressive linkage. The throttle shaft has also been knurled to prevent the linkage arm from slipping. Extensive testing, both on the road and in our state-of-the-art engine dynamometer facility has allowed Edelbrock to offer a power valve and jetting combination that delivers a wide calibration band for smooth and strong performance in various applications. It is finished off with a zinc-diChromeate coating for durability and classic looks.

    Features Include:
  • Machined and assembled by Edelbrock in the U.S.A.
  • Features a 3-bolt flange and cast aluminum base
  • Includes calibration instructions for Flathead and small cubic inch V8 engines
  • Match with an Edelbrock intake manifold, cylinder heads, linkage, fuel blocks and Classic series accessories for the complete classic look of the early hot rod era
  • Fits any standard 3-bolt intake manifold
Vintage 94™ Two-Barrel Carburetors by Edelbrock
Application Emissions Part #
Edelbrock 94™ Carburetor (primary) 1151
Edelbrock 94™ Carburetor (secondary) 1152
Carb Stud, Nut and Washer Kit - (5/16"-18 x 1-1/4") - 8006
Fuel Pressure Regulator with Chrome Finish (1 to 4 psi) - 1789

VINTAGE MANIFOLD AND CARB KITS
Due to popular demand... we are now offering street rodders the ultimate solution for adding dual, triple or six deuce Edelbrock power! Edelbrock Vintage Manifold and Carb kits offer you the core components you need to install an Edelbrock multiple carburetor and intake manifold setup on your small-block Chevy, Small-block or Flathead Ford - All in one box. They include a new Edelbrock intake manifold with two, three or six of our new Edelbrock 94 carburetors. To make the installation simple, these kits include straight throttle linkage and triple-deuce kits include our exclusive progressive throttle linkage #1033 originally designed by Vic Edelbrock Sr. back in the late 1950's for small-block Chevy. All kits also include high-quality Edelbrock gaskets, carb studs and all of the necessary hardware for a hassle free installation.
Complete your multi-carb setup installation with the Edelbrock Mini Fuel Distribution Block Kit #1281 or Fuel Log Kit (#1283, #1284, #1288, or #1287). Edelbrock Fuel Kits provide everything you would need to supply fuel to your intake manifold and carb setup. They feature high quality polished aluminum mini fuel block or extruded aluminum, classic black neoprene hose, fittings and installation hardware. Together with our Manifold and Carb Kits, you get bolt-on Edelbrock performance and classic looks.
Vintage Manifold and Carburetor Kits by Edelbrock
Application Emissions Part #
Small-Block Chevrolet
Triple Carb Kit for 1955-86 Small-Block Chevy (C-357-B intake manifold) 2015
Triple Carb Kit for Small-Block Chevy with E-Tec or Vortec-Style heads (C-357-B intake manifold) 2016
Six Carb Kit for 283-327 Chevy (X1 Ram Log intake manifold) 2018
 
Ford Flathead
Dual Carb Kit for 1938-48 Ford Flathead (Super Dual intake manifold) 2011
Dual Carb Kit for 1938-48 Ford Flathead (Slingshot intake manifold) 2012
Triple Carb Kit for 1938-48 Ford Flathead (Triple Deuce intake manifold) 2013
Triple Carb Kit for 1949-53 Ford Flathead (Triple Deuce intake manifold) 2014
 
Small-Block Ford
Triple Carb Kit for 289-302 V8 (Triple Deuce intake manifold) 2017
 
Kit Part # Intake Manifold Offset Bracket Carb Qty. Throttle Linkage Carb Gasket Intake Gaskets Intake Bolt Kit Carb Stud Kit Regulator
#2011 #1100 #1145 2 #1032 (Straight) Included - - #8006 #1789
#2012 #1103 - 2 #1032 (Straight) Included - - #8006 #1789
#2013 #1108 #1145 3 #1034 (Straight) Included - - #8006 #1789
#2014 #1109 #1146 3 #1034 (Straight) Included - - #8006 #1789
#2015 #5418 - 3 #1033 (Progressive) Included #7201 #8504 #8006 #1789
#2016 #5414 - 3 #1033 (Progressive) Included #7235 #8516 #8006 #1789
#2017 #5412 - 3 #1033 (Progressive) Included #7220 #8524 #8006 #1789
#2018 #2150 - 6 #1031 (Straight) Included #7201 #8504 #8006 #1789
Edelbrock Installation Note INSTALLATION NOTE: See listings in the manifold section for manifold specs.

EDELBROCK 94™ STRAIGHT THROTTLE LINKAGE KITS
These throttle linkage kits are a non-progressive linkage for Edelbrock 94™ carburetors. They are available for dual, triple and six carburetor set-ups and are adjustable to fit various carb spacing. These are the most complete kits on the market - including return spring and bracket, linkage with provision for kick down and throttle connection. Edelbrock 94™ carburetors are equipped with an extended length throttle shaft, making these kits a bolt-on to Edelbrock 94™ carbs.
Edelbrock 94™ Throttle Linkage Kits by Edelbrock
Application Emissions Part #
Edelbrock 94™ Six Carburetor Straight Linkage Kit 1031
Edelbrock 94™ Dual Carburetor Straight Linkage Kit 1032
Edelbrock 94™ Triple Carburetor Straight Linkage Kit 1034

EDELBROCK 94™ PROGRESSIVE THROTTLE LINKAGE KIT
Vic Edelbrock Sr. invented the triple carburetor progressive linkage providing a bolt-on linkage solution for multiple carburetor set-ups on small-block V8 applications. The original design has been re-introduced, giving you the genuine look of the 1950's and 60's. The progressive design opens the primary carburetor(s) to part throttle, then synchronizes all three carburetors to achieve wide-open throttle simultaneously. These are the most complete kits on the market - including return springs and brackets, linkage with provision for kick down and throttle connection. Edelbrock 94 carburetors are equipped with an extended length knurled throttle shaft, making these kits an easy bolt-on upgrade. This unique design saves fuel, provides smoother throttle operation and eliminates flat spots.
Edelbrock 94™ Triple Carburetor Progressive Linkage Kit by Edelbrock
Application Emissions Part #
Edelbrock 94™ Triple Carburetor Progressive Linkage Kit - 1033

EDELBROCK 94™ BALL-END THROTTLE LINK
Replacement throttle linkage arm for early Ford vehicles with passenger side throttle operation.
Edelbrock 94™ Ball-End Throttle Link Arm by Edelbrock
Application Emissions Part #
Edelbrock 94™ Ball-End Throttle Link Arm - 1159

EDELBROCK 94™ ROUND CHROME AIR CLEANER
Replacement throttle linkage arm for early Ford vehicles with passenger side throttle operation.
Edelbrock 94™ Round Chrome Air Cleaner by Edelbrock
Application Emissions Part #
Edelbrock 94™ Round Chrome Air Cleaner 1202

EDELBROCK 94™ CARBURETOR JETS
Intended for tuning the Edelbrock 94™ carburetor, but will also fit original Holly 94's and its later variations.
Edelbrock 94™ Carburetor Jets by Edelbrock
Application Jet Size Emissions Part #
Edelbrock 94™ Carburetor Jet .048" - 1157
Edelbrock 94™ Carburetor Jet .049" - 1160
Edelbrock 94™ Carburetor Jet .050" - 1161
Edelbrock 94™ Carburetor Jet .051" - 1162
Edelbrock 94™ Carburetor Jet .052" - 1163
Edelbrock 94™ Carburetor Jet .053" - 1164
Edelbrock 94™ Carburetor Jet .054" - 1165
Edelbrock 94™ Carburetor Jet .055" - 1166
Edelbrock 94™ Carburetor Jet .056" - 1167
Edelbrock 94™ Carburetor Jet .057" - 1168

EDELBROCK 94™ CARBURETOR POWER VALVES
Edelbrock 94™ Carburetor Power Valves by Edelbrock
Application Vacuum Emissions Part #
Edelbrock 94™ Carburetor Jet 4.5" (Hg) - 1170
Edelbrock 94™ Carburetor Jet 5.5" (Hg) - 1171
Edelbrock 94™ Carburetor Jet 6.5" (Hg) - 1172
Edelbrock 94™ Carb Power Valve Block Off - - 1174

EDELBROCK 94™ CARBURETOR FUEL FITTING
Edelbrock 94™ Carburetor Fuel Fitting by Edelbrock
Application Emissions Part #
Edelbrock 94™ Carburetor Fuel Fitting - 1158

EDELBROCK 94™ CARBURETOR CHOKE CABLE BRACKET
This choke bracket kit provides users with a means of holding a manual choke cable in place upon attaching the cable pull to the carburetor. It includes the bracket and associated hardware. It is a replica of the original Ford bracket that mounted to the carburetor.
Edelbrock 94™ Carburetor Choke Bracket Kit by Edelbrock
Application Emissions Part #
Edelbrock 94™ Carburetor Choke Bracket Kit - 1156

EDELBROCK 94™ CARBURETOR CHOKE CABLE
The Edelbrock Universal Choke Cable for 2-barrel and 4-barrel applications. This cable measures 72" in length and features a stainless steel outer sleeve. The knob is polished and features an engraved Edelbrock Equipped logo. This Edelbrock Universal Choke Cable is a nice way to finish off any carburetor installation.
Edelbrock 94™ Carburetor Choke Cable with Polished Knob by Edelbrock
Application Emissions Part #
Universal Edelbrock 94™ Carburetor Choke Cable with Polished Knob - 8013

EDELBROCK 94™ CARBURETOR HEAT INSULATOR SPACER
This is a 1/4" heat insulator spacer kit for Edelbrock 94™ Series and Stromberg 97® 3-bolt carburetors. The black wood laminate fiber spacer is ideal for reducing heat transfer from the intake manifold to the carburetor. Includes all necessary hardware for a complete installation.
Heat Insulator Spacer for Edelbrock 94™ and Stromberg 97® Carburetors by Edelbrock
Application Emissions Part #
Heat Insulator Spacer for Edelbrock 94™ and Stromberg 97® Carburetors - 8751

EDELBROCK 94™ CARBURETOR REBUILD KIT
This kit has everything needed to rebuild any Edelbrock 94 carburetor. Includes fuel inlet seat, fuel inlet needle, accelerator pump assembly, accelerator pump spring, accelerator check ball, check ball retainer, power valve assembly, float gauge and all necessary gaskets.
Edelbrock 94™ Carburetor Rebuild Kit by Edelbrock
Application Emissions Part #
Edelbrock 94™ Carburetor Rebuild Kit - 1154

EDELBROCK 94™ CARBURETOR REBUILD KIT
The Edelbrock Mini Triple Feed allows the user to plumb a dual or triple carb setup from the fuel pump to the carb. Dual carb applications will require pipe plug #662043 or similar 1/4" -18 NPT plug to block off the third outlet. This kit comes complete with four 1/4" NPT brass fittings, polished aluminum mini fuel block #1286, eight Corbin self-tightening clamps and 5 ft. of classic black neoprene hose. Neoprene hose features internal braid for added strength with a 3/8" inside diameter. Includes the block, fittings, fuel hose, and clamps.
Edelbrock 94™ Mini Triple Fuel Block Kit by Edelbrock
Application Emissions Part #
Edelbrock 94™ Mini Triple Fuel Block Kit - 1281
Edelbrock Installation Note INSTALLATION NOTE: Installations with 5/16" feed line will need fitting #697020 or similar 1/4" NPT x 5/16" barb fitting.

EDELBROCK 94™ FUEL LOG KITS
These Fuel Log kits are exact replicas of the original designs used by Vic Sr. in the 1950's. They are made from extruded aluminum tube with a 3/8" threaded outlet at each end and a polished finish. Kit includes, black neoprene hose, Corbin self-tightening clamps, barb fittings, 3/8" pipe plug and a period-correct Edelbrock decal for the right look. Dual-quad kit #1283 can be used with Edelbrock 94, Performer and Thunder AVS applications. Triple deuce kits #1284 and #1288 are for use with Edelbrock 94 and similar applications. Finally, kit #1287 is intended for use with the Edelbrock Ram Log intake manifold or similar six carburetor application.
Edelbrock 94™ Fuel Log Kit by Edelbrock
Application Emissions Part #
Dual-Quad Fuel Log Kit (6-7/16" outlet spacing) - 1283
Triple Deuce Fuel Log Kit (4-7/8" outlet spacing) - 1284
Triple Deuce Fuel Log Kit (5-1/2" outlet spacing) - 1288
Six Carburetor Fuel Log Kit - 1287
Edelbrock Installation Note INSTALLATION NOTE: Installations with 5/16" feed line will require a 3/8" NPT x 5/16" barb fitting. The end outlet can also be used to run a fuel pressure gauge if desired.

EDELBROCK FLATHEAD TOP END GASKET SETS
Edelbrock is now offering a complete top end gasket set for the Ford/Mercury flathead V8 engine. Each kit includes two cylinder head gaskets and one intake manifold gasket.
Edelbrock Flathead Top End Gasket Sets by Edelbrock
Application Emissions Part #
Top End Gasket Set for 1938-48 Ford/Mercury Flathead - 7384
Top End Gasket Set for 1949-53 Ford/Mercury Flathead - 7383

Edelbrock Tech Note PRODUCT EMISSIONS GUIDE
The following guide is designed to help you determine which Edelbrock components are legal for use on your vehicle. Learn more about Edelbrock Product Emissions Guide.

    50-State Legal
    For Racing Use ONLY
    For Use on Pre-Pollution Controlled Vehicles (PPCV)
    Stock Replacement Part
    Engine Swaps