Edelbrock Cylinder Head Accessories


HEAD BOLT KITS
Edelbrock Head Bolt Kits contain a complete set of the highest quality head bolts and hardened washers available. Cold-formed to ensure molecular integrity and heat treated prior to thread rolling and machining. Reduced diameter bolt heads eliminate the need for valvetrain removal to facilitate cylinder head re-torquing. Hardened and parallel-ground washers are included. Rated at 170,000 p.s.i.
Cylinder Head Bolt Kits by Edelbrock
Application Emissions Part #
AMC Head Bolt Kit for pre-1970 engines - 8531
AMC Head Bolt Kit for 1970 & later engines - 8532
Buick Head Bolt Kit for 400, 430 & 455 engines - 8503
S/B Chevrolet Head Bolt Kit - 8550
Chevrolet Gen III LS1 Head Bolt Kit for Edelbrock & GM Gen III LS1 heads - 8596
Chevrolet Gen IV Head Bolt Kit for Edelbrock heads used on LS series engines 2004 and later - 8595
B/B Chevrolet Head Bolt Kit (not for stock heads, Mark IV only) - 8551
B/B Chevrolet Head Bolt Kit for #77409, #77419, #77429, #77459, #77469, #77479, #77489, #61409 (not for stock heads) - 8554
Chevrolet 409 Head Bolt Kit - 8581
S/B Chrysler Head Bolt Kit (not for stock heads) - 8555
Chrysler Magnum Head Bolt Kit for Edelbrock and '92 and up Magnum heads - 8577
B/B Chrysler Head Bolt Kit - 8591
B/B Chrysler Victor Head Bolt Kit - 8592
Ford Flathead Head Stud Kit for 1938-48 Fords - 8505
Ford Flathead Generator Stud Kit for 1938-48 Fords - 8506
Ford Flathead Head Stud Kit for 1949-53 Fords - 8502
Ford 289-302 Head Bolt Kit (7/16" bolt diameter, use bushings #9680) - 8552
Ford 351-Windsor Head Bolt Kit (1/2" bolt dia., used on 351W with 1/2" threads) - 8553
Ford 302-Clevor Head Bolt Kit 7/16" bolt diameter, includes bushings #9680 - 8562
Ford 351-Cleveland Head Bolt Kit - 8560
Ford FE 390-428 Head Bolt Kit - 8557
Ford 429/460 Head Bolt Kit - 8566
Oldsmobile Head Bolt Kit - 8558
Pontiac Head Bolt Kit for #60509, #60579 and #60599 made before 3/15/02 (not for stock heads) - 8556
Pontiac Head Bolt Kit for #60509, #60579, #60587 and #60599 made after 3/15/02 (not for stock heads) - 8549
Pontiac D-Port Head Bolt Kit (not for stock heads) - 8561

HEAD BOLT BUSHINGS WITH INTEGRAL WASHERS
Allows the use of stock or Edelbrock 7/16" head bolts on Edelbrock heads with 1/2" head bolt bosses. Required for 289-302 V8's and 1967-69 AMC.
Cylinder Head Bolt Bushings with Integral Washers by Edelbrock
Application Emissions Part #
For Ford 5.0L (20 per package) - 9680
For 1969 & Earlier AMC (28 per package) - 9693
For 1966-69 AMC (4 deck dowels per package) - 9652

PUSHROD GUIDEPLATES FOR EDELBROCK HEADS
Made from high-grade alloy steel and hardened to 60 Rockwell "C". Stepped plates support pushrods closer to the rockers stabilizing them. Sold in sets of 8.
Cylinder Head Pushrod Guideplates by Edelbrock
Application Emissions Part #
AMC, 5/16" Flat - 9669
S/B Chevy, 5/16" Flat - 9660
B/B Chevy, 3/8" Stepped - 9666
Chevy 348/409 V8, 3/8" Flat - 9609
Chrysler Magnum, 5/16" Flat - 9662
S/B Ford, 5/16" Flat - 9665
351C Ford, 5/16" Flat - 9672
429/460 Ford, 3/8" Stepped - 93669
Oldsmobile, 3/8" Flat - 9668
Pontiac, 5/16" Flat - 9667

HARDENED STEEL PUSHROD SETS
For use in engines with or without hardened steel guideplates. Manufactured from case-hardened tubing with a surface hardening and welded ends for maximum durability. All pushrods are 5/16" in diameter, except for #9605, #9635, #9647, #9648 and #9654 which are 3/8" O.D. Sold in sets of 16.
Hardened Steel Pushrod Sets by Edelbrock
Application Emissions Part #
AMC 343-401 (8.065") - 9637
Buick 400-430-455 (9.655") - 9605
S/B Chevy (7.265", for use with Edelbrock hydraulic roller lifters #97423) - 9646
S/B Chevy (7.800" stock length) - 9630
S/B Chevy (7.900") - 9629
S/B Chevy (7.191", for hydraulic roller lifters) - 9653
Chevy 348/409 "W" (8.650"/9.00") - 9635
Chevy 348/409 "W" (8.300"/ 8.750", for use with Edelbrock hydraulic roller lifters #97423) - 9648
B/B Chevy (8.60" / 7.64", for hydraulic rollers) - 9654
B/B Chevy (7.800"/8.80", for use with Edelbrock hydraulic roller lifters #97433) - 9647
Ford 289-302 (6.805") - 9632
Ford 289-302 (6.385", for hydraulic rollers) ( A ) - 9655
Ford 289-302 (6.430", for hydraulic rollers) ( A ) - 9658
Ford 289-302 (7.714", for use with Edelbrock hydraulic roller lifters #97453) - 9659
Ford 351W (8.152") - 9636
Ford 351W (7.634", for hydraulic rollers) - 9656
Ford 351M/400 (9.508") - 9633
Magnum 5.2L/5.9L (6.936") - 9638
Edelbrock Installation Note INSTALLATION NOTE: Refer to lifter kit #97453

ROCKER STUDS
These high-quality rocker studs are used in all Edelbrock cylinder heads requiring 3/8" screw-in studs. Sold in packaged quantities of two or sixteen.
Cylinder Head Rocker Studs by Edelbrock
Application Emissions Set of 2 Set of 16
Rocker Studs - 8598 8599

REPLACEMENT VALVES
1-piece, swirl-polished, hardened tip stainless steel valves with undercut stems for increased flow. Hard-chromed valve stems are 11/32" except where noted.
Replacement Intake & Exhaust Valves by Edelbrock
Application Emissions 1 Only Set of 8
INTAKE VALVES
1.90" for #60229, #60329 - 9764 9769
1.90" for #60379 - 9763 9768
1.94" for #60979, #61909 - 9774 9779
2.02" for #60399 - 9778 9777
2.02" for #60779, #60179 - 9365 9366
2.02" for #60989, AMC, S/B Chevy & Ford (except #60399) - 9760 9765
2.05" for #77169, #77179, #77189, #77199 - 9370 9371
2.072" for #60519 - 9375 9376
2.08" for #77619, #77629, #77639, #77649 (.100" longer than stock.) - 9784 9785
2.09" for #60069, #60079 (3/8" stem) - 9754 9755
2.11" for #60579, #61579, #61599 - 9781 9780
2.11" for #60599 (Ram Air IV length .120" longer than stock) - 9750 9751
2.14" for #60929 - 9740 9741
2.19" for #60459, #60479, #60499, #60559 - 9770 9775
2.19" for #60669, #60689 - 93661 93662
2.19" for #60679, #60699, #61669, #61649 - 93770 93771
2.19" for #60809, #60819 - 93780 93781
2.20" for #77919, #77929, #77939, #77949 - 93774 93775
2.25" for #61459, #61559 - 97040 97041
2.30" for #77409 (.400" longer than stock) - 9360 9361
 
EXHAUST VALVES
1.55" for #60979, #61909 - 9772 9773
1.60" for #60229, #60259, #60329, #60359, #60989, AMC, S/B Chevy - 9761 9766
1.60" for #60379, #60399 - 9762 9767
1.60" for #60779, #60179 - 9367 9368
1.60" for #77619, #77629, #77639, #77649 (.100" longer than stk.) - 9786 9787
1.60" for #77169, #77179, #77189, #77199 - 9372 9373
1.66" for #60069, #60079 (3/8" stem) - 9756 9757
1.66" for #60579, #61579, #61599 - 9783 9782
1.66" for #60599 (Ram Air IV length .120" longer than std.) - 9752 9753
1.68" for #60519 - 9317 9318
1.72" for #60809, #60819 - 93782 93783
1.76" for #60669, #60689 - 93663 93664
1.76" for #60679, #60699, #61669, #61649 - 93772 93773
1.81" for #60929, #60189 - 9642 9643
1.81" for #77919, #77929, #77939, #77949 - 93776 93777
1.88" for #60459, #60479, #60499, #60559 - 9771 9776
1.89" for #61459, #61559 (Inconel) - 9789 9788
1.90" for #77409 (+.100") - 9362 9363

REPLACEMENT VALVE SEATS
Replacement Valve Seats by Edelbrock
Application Emissions Part #
Replacement Valve Seats - 9709
S/B Chevy, 1.60" (exhaust) - 9710
S/B Ford, 1.90" (intake) Set of 8 - 9711
LT1/E-Tec, 1.94" (intake) - 9712
Pontiac, 2.11" (intake) - 9713
Pontiac, 1.66" (exhaust) - 9714
B/B Chevy, 2.19" (intake) - 9716
B/B Chevy, 1.88" (exhaust) - 9717
Ford FE, 2.09" (intake) - 9718
Ford FE, 1.66" (exhaust) - 9719

RED ROLLER ROCKER ARMS
Edelbrock red roller rockers are manufactured in the USA from lightweight 7129 grade aluminum. The body is CNC machined then micro polished and anodized for durability. The trunnion race, roller pin and roller tip are centerless ground for superior quality. A high quality Torrington needle bearing fulcrum combined with a roller tip ensure smooth operation and performance. The full body design will accommodate up to 1.65" diameter springs. Thick-walled adjusting nuts and 4140 steel poly locks are included.
Red Roller Rocker Arms by Edelbrock
Application Emissions 1 Only Set of 16
Small-Block Chevy, 3/8", 1.5:1 ratio - 77771 77770
Small-Block Ford, 3/8", 1.6:1 ratio - 77781 77780
Big-Block Chevy, 7/16", "W" 348/409, 1.7:1 ratio - 77791 77790

REPLACEMENT GUIDES AND SEALS
Manganese-bronze valve guide (one each) for Performer & Performer RPM heads, except as noted.
Replacement Guides and Seals by Edelbrock
Application Emissions Intake Exhaust
VALVE GUIDES
S/B Chevy, S/B & B/B Chrysler, S/B Ford, Olds, Pontiac (Ram Air IV) - 9701 9701
B/B Chevy - 9702 9703
Ford FE (for all Edelbrock FE heads) - 9704 9704
S/B Ford (for Victor heads #77219) - 9702 9706
 
Application Emissions Part #
VALVE SEALS (Set of 16)
11/32" (for all Edelbrock Performer & Performer RPM heads, except Ford FE) - 9725
11/32" (S/B Chevy, S/B Ford Victor Jr. & B/B Chrysler Victor heads) - 9758
3/8" (Ford FE, earlier design with .530" guide o.d.) - 9726
3/8" (Ford FE, current production with .562" guide o.d.) - 9759

REPLACEMENT VALVE SPRING LOCATORS & SEAT CUP KITS
Valve Spring Locators and Seat Cups provide a hardened barrier between the springs and the aluminum heads, positively locating the base of the spring to prevent unwanted spring movement. Sold in sets of 16.
Replacement Vlave Spring Locators and Seat Cup Kits by Edelbrock
Application Emissions Part #
Spring Seat Cup Kit (.060" thick, requires 1.65" diameter counterbore) for Edelbrock S/B Chevy, 289-351W Ford, 318-360 Chrysler and Pontiac heads using springs #5767/#5825 - 5769
Spring Seat Cup Kit (.060" thick, requires 1.73" diameter counterbore) for Edelbrock 390-428 Ford FE and 383-440 Chrysler heads using valve springs #5792 - 5771
Valve Spring Locators (.805" i.d., 1.540" o.d.) for Edelbrock B/B Chevy and 460 Ford heads using valve springs #5745 - 5770
Spring Seat Locator/Seal Kit (8mm valves and conical springs) for use on Edelbrock LS & E-CNC heads w/8mm stem valves combined with 1.30" conical (beehive style) springs - 5766

VALVE STEM LOCKS
Heat-treated machined (HTM) 7° valve stem locks for use with Edelbrock retainers. Black oxide, top-quality steel for maximum strength.
Vlave Stem Locks by Edelbrock
Application Diameter Taper Material Emissions Part #
Single groove (set of 32) 11/32" Heat treated stamped steel - 9611
Single groove (set of 32) 3/8" Heat treated stamped steel - 9612
Single groove (set of 24) 11/32" Heat treated stamped steel - 9614
Single groove, .050" low (set of 32) 11/32" 4140 machined hardened steel - 9615
Single groove, std. height (set of 32) 11/32" 4140 machined hardened steel - 9616
Single groove (set of 32) 8MM Heat treated steel - 9657

Edelbrock Tech Note PRODUCT EMISSIONS GUIDE
The following guide is designed to help you determine which Edelbrock components are legal for use on your vehicle. Learn more about Edelbrock Product Emissions Guide.

    50-State Legal
    For Racing Use ONLY
    For Use on Pre-Pollution Controlled Vehicles (PPCV)
    Stock Replacement Part
    Engine Swaps