Performer RPM SCCA Cylinder Heads For S/B Ford


Performer RPM SCCA Cylinder Heads for S/B Ford by Edelbrock
 
  • Cylinder Head Specifications:
  • Combustion chamber volume: 60cc
  • Intake runner volume: 170cc
  • Exhaust runner volume: 60cc
  • Intake valve diameter: 1.94"
  • Exhaust valve diameter: 1.55"
  • Valve stem diameter: 11/32"
  • Valve guides: Manganese bronze
  • Deck thickness: 5/8"
  • Valve spring diameter: Springs NOT Included
  • Valve spring maximum lift: N/A
  • Rocker stud: 3/8"
  • Guideplate: Hardened steel
  • Pushrod diameter: 5/16"
  • Valve angle: 20°
  • Exhaust port location: Stock
  • Spark plug fitment: 14mm x 3/4 reach, gasket seat
 
These heads are designed exclusively for the SCCA American Sedan Series Class. They feature 1.94" intake, 1.55" exhaust valve sizes and non interlocking valve seats. To comply with class rules, there is no blending work in the intake entries, exhaust exits or bowl area of the intake or exhaust. The casting is manufactured of A356 aluminum and heat treated to T6 spec for superior quality. All heads include manganese-bronze valve guides, one-piece stainless steel valves with hardened tips, ductile iron valve seats and Heli-Coil® threaded inserts in the exhaust and rocker stud holes. Bare heads will require final sizing of the valve guides and proper valve job prior to the installation of valves. All Edelbrock SCCA RPM heads are engraved with the SCCA approved logo and are legal for the American Sedan Class. For additional information, please refer to the SCCA rule book. Match with the SCCA approved Performer RPM intake, #7121.
  Bare (Single) Complete (Single)
Application Dyno Emissions Satin Satin
EQUIPPED WITH SPRINGS FOR USE IN HYDRAULIC FLAT TAPPET CAMSHAFT APPLICATIONS
Performer RPM SCCA - 602479 602579
Edelbrock Installation Note INSTALLATION NOTE: Hardened pushrods required, use Edelbrock #9632 (flat tappet only). Will not accept rail rockers. 289-302 V8s require Head Bolt Bushings #9680 and either Head Bolt Kit #8552 (7/16") or stock head bolts. Match with Edelbrock head gasket sets. Bare heads will have valve guides and seats installed, but will require final sizing and a valve job to match the valves you will be using. Recommended spark plugs are Champion RC12YC or equivalent 14mm x 3/4" reach with flat gasket seat. This head does not include valve springs due to the wide variety of camshafts used in competition. Please consult your camshaft manufacturer for appropriate valve spring selection. Deck thickness: 5/8", rocker stud diameter: 3/8", pushrod diameter: 5/16" (width of slot in guide plate).
#602579: Flow Numbers as tested by Edelbrock's SuperFlo SF-1020 flow bench @ 28" H2O
Valve Lift .100" .200" .300" .400" .500" .600" .700"
Intake 62 122 175 213 228 232 -
Exhaust 50 93 125 140 146 150 -
Edelbrock Tech Note TECH NOTE: Please view Cylinder Head Flow Data and Valve Springs & Retainers for all Edelbrock Performance Aluminum Cylinder Heads.
Edelbrock Tech Note PRODUCT EMISSIONS GUIDE
The following guide is designed to help you determine which Edelbrock components are legal for use on your vehicle. Learn more about Edelbrock Product Emissions Guide.

    50-State Legal
    For Racing Use ONLY
    For Use on Pre-Pollution Controlled Vehicles (PPCV)
    Stock Replacement Part
    Engine Swaps