Edelbrock Victor Series Manifolds For Chevy 13°-18°


CHEVROLET 262-400 SMALL-BLOCK V8
VICTOR 18° ONE-PIECE DESIGN (5000-8500 RPM)
Designed for use on 9.5:1 compression engines with 390 cfm carbs and GM or Edelbrock 18° heads. Runners have a 2.9 square-inch cross-section. Manifold height from the end seal to the carb pad is 7.03". The Victor 18° #2959 features intake runners with a large cross-section area of 3.2 square-inches for max high-end horsepower in engines operating from 5000 to 8500 rpm with GM or Edelbrock 18° heads. #2995 is designed for engines using Edelbrock or GM 18° High-Port heads #10134363 and #10134364, #2995 runners have a 2.85 square-inch cross-section. Features 1/2" female pipe bosses over rear water outlets to allow for customization of cooling system and dual distributor clamp locations for ease of timing adjustment. Relief for center water outlets included.
S/B Chevy 18° One-Piece Design Victor Series Intake Manifolds by Edelbrock
Application Dyno Emissions Part #
Victor 18° 3.2 - 2959
Victor 18° High-Torque - 2995
Water By-Pass Kit for #2995 - - 8095
Edelbrock Installation Note INSTALLATION NOTE: Recommended intake gasket: Edelbrock #7218 (#2995), Fel-Pro #1282. For the heights of all Edelbrock manifolds, please visit the the Manifold Reference Dimensions page.

CHEVROLET 262-400 SMALL-BLOCK V8
VICTOR 18° SPIDER (5000-8500 RPM)
Victor 18° 2.9 Spider #2955 has the same plenum and runner design as #2950 but in a spider configuration. The Victor 18° #2958 features intake runners with a large cross-section area of 3.2 square-inches for maximum high-end horsepower in engines with GM or Edelbrock 18° heads. Must use Edelbrock base plate #2992.
S/B Chevy 18° Spider Victor Series Intake Manifolds by Edelbrock
Application Dyno Emissions Part #
Victor 18° 2.9 Spider - 2955
Victor 18° 3.2 Spider - 2958
Victor Valley Plate - - 2992
Edelbrock Installation Note INSTALLATION NOTE: Recommended intake gasket: Edelbrock #7218 or Fel-Pro #1282, #1254 (base). For the heights of all Edelbrock manifolds, please visit the the Manifold Reference Dimensions page.

CHEVROLET 262-400 SMALL-BLOCK V8
VICTOR 15°-18° CHEVY (5000-8500 RPM)
Designed with noted drag racer Billy Glidden, Victor Glidden #2859 is for all-out nitrous-assisted drag race applications. It features intake runners with a large cross-section area of 3.2 square-inches for maximum high-end horsepower in engines operating from 5000 to 8500 rpm with GM or Edelbrock 18° heads. Carb mount flange and plenum are machined for 4500 Series carbs and require port matching and blending prior to use.
S/B Chevy 15°-18° Victor Series Intake Manifolds by Edelbrock
Application Dyno Emissions Part #
Victor Glidden (for 15° and 18° Chevy with 4500 Series carburetor) - 2859
Edelbrock Installation Note INSTALLATION NOTE: Recommended intake gasket: Edelbrock #7218 or Fel-Pro #1282. For the heights of all Edelbrock manifolds, please visit the the Manifold Reference Dimensions page.

CHEVROLET 262-400 SMALL-BLOCK V8
VICTOR GLIDDEN 15°-18° SPIDER (5000-8500 RPM)
Intended for 375 c.i. and up high output drag race engines, this manifold was developed in conjunction with noted drag racer Billy Glidden and is specifically designed to complement the flow characteristics of fully ported 18° and 15° cylinder heads. It features a 4500 series carb flange, and the dividers are pulled back to increase plenum size and shorten the runners for improved high rpm performance. The runners are wider at the plenum, producing approximately 3.6 square inches area at the opening.
S/B Chevy 15°-18° Victor Glidden Intake Manifolds by Edelbrock
Application Dyno Emissions Part #
Victor Glidden Spider-Type Manifold (for 15° and 18° heads) - 2858
Victor 18 Base (base of two-piece manifold) - 2992
Edelbrock Installation Note INSTALLATION NOTE: Must be used with Edelbrock base plate #2992. Recommended intake gasket: Edelbrock #7218 or Fel-Pro #1282 (spider and manifold), #1254 (base). For the heights of all Edelbrock manifolds, please visit the the Manifold Reference Dimensions page.

CHEVROLET 262-400 SMALL-BLOCK V8
VICTOR TWO-PIECE DESIGN (5000-8500 RPM)
The Victor Two-Piece manifolds were developed to simplify CNC manifold porting. They are supplied in right and left halves that can be machined and then assembled with the supplied bolts and o-ring. Victor Two-Piece manifolds are available for various applications from standard 9" deck 18° cylinder heads to 9.3" deck Clements/Dart 13° cylinder heads as well as SB2 and ROX engines. They are also offered in varying flange thicknesses to accommodate multiple applications.
Chevy Two-Piece Victor Series Intake Manifolds by Edelbrock
Application Bore Center Flange Thickness Maximum Deck Height Emissions Manifold Part # Valley Plate #
Conventional 18° Cylinder Heads 4.4" Standard 9.000" 2846 2855
Brodix, All Pro & Dart (13° hi-port designs) 4.4" 0.747" 9.080" 2844 2855
Brodix 13° 4.5" Standard 9.080" 2840 2855
Conventional 18° cylinder heads, Brodix, All Pro & Dart 4.4" 0.989" 9.300" 28468 2856
Brodix 13° 4.5" 0.990" 9.300" 28408 2856
Dart 9° 4.4" Standard 9.080" 2842 2855
Dart 9° 4.4" 0.990" 9.500" 28428 2856
Dart 9° 4.5" Standard 9.080" 2843 2855
Dart 9° 4.5" 0.990" 9.500" 28438 2856
Brodix 10° 4.5" Standard 9.080" 2845 2855
Brodix 10° 4.5" 0.990" 9.500" 28458 2856
SB2 4.4" Standard 9.080" 2847 2853
SB2 4.4" 0.990" 9.500" 28478 28538
ROX 4.5" Standard 9.080" 2848 2851
ROX 4.5" 1.070" 9.500" 28488 28518
Edelbrock Installation Note INSTALLATION NOTE: Conventional 18° applications will require additional machining of manifold and valley plate for desired clearance when using valley plate #2855. Valley plate #2992 can also be used when less machining is desired. When using thick flange manifolds, machining of backside of flange is recommended for weight reduction. For the heights of all Edelbrock manifolds, please visit the the Manifold Reference Dimensions page.

Edelbrock Tech Note PRODUCT EMISSIONS GUIDE
The following guide is designed to help you determine which Edelbrock components are legal for use on your vehicle. Learn more about Edelbrock Product Emissions Guide.

    50-State Legal
    For Racing Use ONLY
    For Use on Pre-Pollution Controlled Vehicles (PPCV)
    Stock Replacement Part
    Engine Swaps