Edelbrock Manifolds For Ford/Mercury Flathead


1938-53 FORD/MERCURY FLATHEAD V8
SLINGSHOT MANIFOLD
This is a reproduction of the original intake manifold designed by Vic Edelbrock Sr. in 1938. The Slingshot is a real show stopper and even includes stainless acorn nuts for mounting the two halves. Will fit Ford and Mercury engines made from 1938 to 1948. Match with our block letter heads for a classic look. Includes assembly hardware and gasket #8700.
Ford Flathead Slingshot Intake Manifolds by Edelbrock
Application Dyno Emissions Part #
Slingshot Manifold - 1103
Slingshot Manifold Gasket (located between manifold top and bottom pieces) - - 8700
Edelbrock Carburetor Recommendation CARB RECOMMENDATIONS: Edelbrock 94 #1151Carburetor.
Edelbrock Installation Note INSTALLATION NOTE: Use linkage kit #1032; carb stud kit #8006. Recommended intake gasket: Edelbrock #7234 or Fel-Pro #MS2853. Manifold height: A-7.75", B-7.75". Port exit dimensions: 1.3" x 1.7". For the heights of all Edelbrock manifolds, please visit the the Manifold Reference Dimensions page.

1938-53 FORD/MERCURY FLATHEAD V8
SUPER DUAL MANIFOLD
A truly classic race manifold; the Super Dual features 180 firing order, eliminated heat crossover and carb location over port openings. Designed for Ford and Mercury engines made from 1938 to 1948. Available with satin or polished finish
Ford Flathead Super Dual Intake Manifolds by Edelbrock
Application Dyno Emissions Part #
Super Dual Manifold (includes generator bracket #1145) - 1100
Edelbrock Carburetor Recommendation CARB RECOMMENDATIONS: Edelbrock 94 #1151Carburetor.
Edelbrock Installation Note INSTALLATION NOTE: Use linkage kit #1032; carb stud kit #8006; generator stud kit #8506. Recommended intake gasket: Edelbrock #7234 or Fel-Pro #MS2853. Manifold height: A-3.53", B-4.63". Port exit dimensions: 1.3" x 1.7". For the heights of all Edelbrock manifolds, please visit the the Manifold Reference Dimensions page.

1938-53 FORD/MERCURY FLATHEAD V8
TRIPLE DEUCE MANIFOLD
These reproductions of the vintage Edelbrock manifold #SU 359 and #SU 349 allow the use of three 2-barrel carburetors on 1938-1948 and 1949-1953 Ford Flathead engines. #1109 features front road draft and 1-3/8" diameter oil fill bosses and a raised fuel pump boss. They accept #1151 and #1152 Edelbrock 94 3-bolt, Stromberg 3-bolt (97 type), Holley 3-bolt and Demon 98 carburetors.
Ford Flathead Triple Deuce Intake Manifolds by Edelbrock
Application Dyno Emissions Part #
Triple Deuce Manifold for 1938-48 - 1108
Triple Deuce Manifold for 1949-53 - 1109
Edelbrock Carburetor Recommendation CARB RECOMMENDATIONS: Edelbrock 94 #1151Carburetor.
Edelbrock Installation Note INSTALLATION NOTE: Use progressive linkage kit #1033 or non-progressive kit #1034; carb stud kit #8006: generator stud kit #8506. Recommended intake gasket: Edelbrock #7234 or Fel-Pro #MS2853. Manifold height: A-3.66", B-3.66". Port exit dimensions: 1.3" x 1.7". For the heights of all Edelbrock manifolds, please visit the the Manifold Reference Dimensions page.

1938-53 FORD/MERCURY FLATHEAD V8
FORD FLATHEAD 4-BARREL MANIFOLD
This manifold allows the use of square-bore carbs such as the Edelbrock Performer Series or Thunder Series AVS 500 cfm on the 1949-1953 Ford Flathead engine. This is a reproduction of the vintage Edelbrock #452 two-piece manifold with a new carb adapter flange. Carb adapter flange also available separately, #1106.
Ford Flathead 4-Barrel Intake Manifolds by Edelbrock
Application Dyno Emissions Part #
Ford Flathead 4-Barrel Manifold for 1949-53 - 1107
Edelbrock Carburetor Recommendation CARB RECOMMENDATIONS: Edelbrock Performer Series carb, 500 cfm or Thunder Series AVS 500 cfm Carburetor.
Edelbrock Installation Note INSTALLATION NOTE: Recommended intake gasket: Edelbrock #7234 or Fel-Pro #MS2853. Manifold height: A-4.06", B-6.06". Port exit dimensions: 1.3" x 1.7". For the heights of all Edelbrock manifolds, please visit the the Manifold Reference Dimensions page.

GENERATOR BRACKETS
This manifold allows the use of square-bore carbs such as the Edelbrock Performer Series or Thunder Series AVS 500 cfm on the 1949-1953 Ford Flathead engine. This is a reproduction of the vintage Edelbrock #452 two-piece manifold with a new carb adapter flange. Carb adapter flange also available separately, #1106.
Ford Flathead Generator Brackets by Edelbrock
Application Dyno Emissions Part #
1940-41 Generator Bracket (straight) - - 1144
1942-48 Generator Bracket (offset) - - 1145
1949-53 Generator Bracket and Water Neck Kit (offset) - - 1146
1938-48 Generator Bracket Stud Kit - - 8506

Edelbrock Tech Note PRODUCT EMISSIONS GUIDE
The following guide is designed to help you determine which Edelbrock components are legal for use on your vehicle. Learn more about Edelbrock Product Emissions Guide.

    50-State Legal
    For Racing Use ONLY
    For Use on Pre-Pollution Controlled Vehicles (PPCV)
    Stock Replacement Part
    Engine Swaps