|
|
 |
| Back to Ford Main Manifold Page |
|
 |
Ford 260-289-302 V8
PERFORMER RPM 302 (1500-6500 rpm)
Designed for street 289-302 c.i.d. Ford V8s. This dual-plane high rise manifold has excellent
high rpm power while retaining throttle response. #7121 is stock replacement/street legal part
for Shelby Mustangs with 289 c.i.d. V8 with OEM 4V carb; 1965-66. No provisions for exhaust heated choke.
Available with standard finish or polished. Aftermarket 4-bbl carbs are not compatible with Ford Auto
Overdrive Transmission (AOD) unless used with Lokar bracket SRK-4000, see note at bottom of this page.
Available with standard finish or polished, see Optional Finishes.
|
|
| Applications |
Part # |
| Performer RPM 302 (non-EGR) |
#7121 |
| Performer RPM 302 (non-EGR) w/ EnduraShine finish |
#71214 |
| Polished Performer RPM 302 (non-EGR) |
#71211 |
| |
| Carburetor Recommendations:
Edelbrock Thunder Series AVS or Performer Series carb, 600-750 cfm (see Carbs & Accessories),
for auto. trans. use our #1483 & #1490 or #1844 & #1845
 Installation Notes: Will not fit 255 c.i.d. V8. Recommended intake gasket: Edelbrock #7220.
Manifold Height: A-4.30", B-5.50" see A/B Measurements. Port exit dimensions: 1.05" x 1.86".
|
|
|
Ford 351 Windsor V8
PERFORMER RPM 351-W (1500-6500 rpm)
Designed for 1969 and later 351 Windsor Ford V8 high-performance engines with Edelbrock
Performer RPM cylinder heads, modified OEM cylinder heads or equivalent. The dual-plane
design offers good throttle response with excellent top-end power for the street. No provisions for choke or
rear water crossover. Will fit 1964-1/2 to 1970 Mustangs. Will not fit under stock hood of 1974-78 or 1979-
95 Mustangs. Aftermarket 4-bbl carbs are not compatible with Ford Auto Overdrive Transmission (AOD)
unless used with Lokar bracket SRK-4000, see note at bottom of this page.
|
|
| Applications |
Part # |
| Performer RPM 351-W (non-EGR) |
#7181* |
| Performer RPM 351-W w/ Polished Finish (non-EGR) |
#71811* |
| |
| Carburetor Recommendations:
Edelbrock Thunder Series AVS or Performer Series carb, 650-800 cfm (see Carbs & Accessories),
for auto. trans. use our #1483 & #1491 or #1844 & #1846
Installation Notes: Use 12-bolt intake gasket set (Edelbrock #7220 recommended). For van installations
use OEM Ford "van" intake gasket set; will fit early 16-bolt head with Ford 16-bolt intake gasket set.
Manifold height: A-4.30", B-5.30" see A/B Measurements. Port exit dimensions: 1.12" x 1.86". |
| |
|
|
|
Ford 260-289-302 V8 (For Cleveland Heads)
PERFORMER RPM E-BOSS 302 MANIFOLD
With the new Performer RPM E-Boss 302 manifold #7129, you can build a mock Boss engine by using a standard 302 block and Performer RPM Cleveland cylinder heads #61689 or #61699. For high-performance street and competition, our dual-plane design makes outstanding power from 1500 to 6500 rpm. The Cleveland port layout and intake bolt hole pattern fit both 2V and 4V heads. Features include 8.2" deck height, Windsor end rails, water neck and distributor clearance plus front and rear water bosses. Match with an Edelbrock Performer or Thunder Series AVS carburetor. Will not fit OE Boss 302 engines.
Available with standard finish or polished, see Optional Finishes.
|
|
| Applications |
Part # |
| Performer RPM E-Boss 302 Ford manifold |
#7129 |
| |
| Carburetor Recommendations:
Edelbrock Thunder Series AVS or Performer Series carb, 600-800 cfm (see Carbs & Accessories) Recommended intake gasket: Edelbrock #7265. Manifold height: A-4.42", B-5.70"; Carb pad height: 5.06". Port exit dimensions: 1.42" x 2.07". |
|
|
Ford 351W V8 (For Cleveland Heads)
PERFORMER RPM E-BOSS 351 (1500-6500 rpm)
Build a mock Boss 351 engine with a standard 351 block and Edelbrock Performer RPM Cleveland heads using the new Performer RPM E-Boss 351 manifold #7183. For both high performance street and competition, the dual-plane design makes outstanding power from 1500 to 6500 rpm and the Cleveland port layout and intake bolt hole pattern fit both 2V and 4V heads. It features 9.5" deck height, Windsor end rails, water neck and distributor hole clearance, front and rear water bosses with a standard square bore carburetor pad. Edelbrock carbs will work with Ford automatic overdrive trans (AOD) when used with Lokar bracket SRK-4000, for more info call (865) 966-2269 or go to lokar.com.
Available with standard finish or polished, see Optional Finishes.
|
|
| Applications |
Part # |
| Performer RPM 302 (non-EGR) |
#7183 |
| |
| Carburetor Recommendations:
Edelbrock Thunder Series AVS or Performer Series carb, 600-800 cfm (see Carbs & Accessories) Recommended intake gasket: Edelbrock #7265. Manifold height: A-4.42", B-5.70"; Carb pad height: 5.06". Port exit dimensions: 1.42" x 2.07". |
|
Nascar Edition
