Free Shipping on all orders over $50* Learn More
Performer Intake Manifold for Holden V8 253-308 CID Engines

Performer Intake Manifold for Holden V8 253-308 CID Engines

Performer RPM 4V/Q-JET Marine Intake Manifold for 87-95 Small-Block Chevy

Performer RPM 4V/Q-JET Marine Intake Manifold for 87-95 Small-Block Chevy

Performer RPM 4V/Q-JET Marine Intake Manifold for 55-86 Small-Block Chevy

$576.95
Performer RPM Q-JET Marine Intake Manifold For 1986 & Earlier Small-Block Chevrolet 262-400 V8's. All Cooling Water Passages are Lined with Brass to Prevent Corrosion. The Carb Pads Accept Either Q-Jet or Square-Bore Marine Carburetors
In stock
SKU
2504
Edelbrock part #2504 Performer RPM Q-Jet marine intake manifold is designed for 1955-86 262-400 c.i.d. Chevy V8's for spread-bore (Q-Jet) or square-bore carbs. This Performer RPM Q-Jet intake manifold is designed specifically for demanding marine applications and delivers maximum power and a broad torque curve for high-performance marine.
More Information
Manufacturer Edelbrock
Application Application Specific
UPC 00085347025046
Series Performer RPM
Grade Type Performance
Gasket Or Seal Included No
Vehicle Model Chevrolet
Availability Note Available to Order
Warranty 12 Months
RPM Range 1500-6500 RPM
Emissions Code
Hazardous Materials Warning WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
Installation Notes
  • Manifold ht: A-4.20", B-5.25" (.70" taller than #2101); Carb pad height: 4.27"; Carb recommendations: Edelbrock #1409 or #1410; For the heights of all Edelbrock manifolds, please visit the Manifold Reference Dimensions page. http://www.edelbrock.com/automotive/mc/manifolds/reference-dimensions.shtml; Port exit dimensions: 1.16" x 1.92"; Recommended intake gasket: Edelbrock #7201.; Use RTV sealant to properly seal end seals, such as Edelbrock High Temp Silicone sealant #1076, DO NOT USE END SEALS GASKETS.; Use #8504 Edelbrock bolt kit; Sealant must be used on intake bolt threads if the threads extend into lifter valley or coolant passage.; NPT/Pipe thread fittings require the use of Teflon tape or paste on threads to ensure proper seal.; DO NOT OVERTIGHTEN NPT/Pipe fittings, this may cause the aluminum to crack around the fitting boss. NPT/Pipe thread is a tapered thread.; Hardened washers Must be used with intake bolts to ensure proper torque and prevent galling of the aluminum.; Will not fit under stock Corvette hood.; Edelbrock does not recommend the use of an economy type carburetor such as the Performer series #1406 or #1411 on Performer RPM Intake Manifolds. Economy type carburetors are calibrated lean for fuel economy and will not perform properly on this style of intake.; A carb flange and plenum design that works well with spread-bore (Q-Jet) or square-bore carburetors without the need for adaptors.; Has provision for exhaust heated divorced choke for Q-Jet Carbs.; Use Edelbrock rod #9172 for divorced choke with Q-Jet.; Even though manifolds are compatible with EGR systems, this does not mean they are legal for use on emissions controlled vehicles. Check local laws for legality.; Proper installation is the responsibility of the installer. Improper installation will void your warranty and may result in poor performance and engine or vehicle damage.
Color Satin
Finish Satin
Material Aluminum
Rear Maximum Height 5.250 in
Single Or Dual Plane Type Dual